RLVa RFC setsphere

Mode: Blur (2)

Command	Value(s)	Description
setsphere_mode	2	Switches @setsphere to 'variable kernel blur' mode
setsphere_param	<kernel size>/0/0/0	The first number specifies the kernel size for the Gaussian blur (needs to be set in combination with valuemin/valuemax)
setsphere_distmin	<distance>	Sets the distance (in m) at which the effect should start
setsphere_distmax	<distance>	Sets the distance (in m) at which the effect should end
setsphere_distextend	0, 1, 2 or 3	See documentation above
setsphere_valuemin	<float>	Sets the strength of the effect at distmin (useful range values depend on kernel size param)
setsphere_valuemax	<float>	Sets the strength of the effect at distmax (useful range values depend on kernel size param)

Notes

• The kernel size determines how many neighbouring pixels are sampled. A higher kernel size will result in a more blurred out end result (dependent on the sigma value in min/max value)
• Avoid using large value for kernel since this will likely be clamped in the future once the impact on FPS can be determined

Example

1. Clear all modifiers and switch @setsphere to 'variable blur' mode

   @clear,setsphere=n,setsphere_mode:2=force

2. Set the kernel size to 15 and sigma value to 5

   @setsphere_param:15/0/0/0=force,setsphere_valuemax:5=force

3. Enforce the effect only when >=2m away (only objects >2m will look blurry)

   @setsphere_distmin:2=force

(Step 2) Red shifted by 8 left and 0 down. Blue shifted by 8 right and 0 down.

(Step 3) Using valuemin/valuemax blends the original colour with the effect making it appear more like a ghost artifact

Mode: Chromatic Aberration

Command	Value(s)	Description
setsphere_mode	3	Switches @setsphere to 'chromatic aberration' mode
setsphere_param	<horiz red shift>/<vert red shift>/<horiz blue shift>/<vert blue shift>	The first 2 numbers specify the offset of the red component; the last 2 the offset of the green component
setsphere_distmin	<distance>	Sets the distance (in m) at which the effect should start
setsphere_distmax	<distance>	Sets the distance (in m) at which the effect should end
setsphere_distextend	0, 1, 2 or 3	See documentation above
setsphere_valuemin	0.0-1.0	Sets the strength of the effect at distmin
setsphere_valuemax	0.0-1.0	Sets the strength of the effect at distmax

Notes

• If both values (valuemin and valuemax) and both distances (distmin and distmax) are different then - much like the blending mode - the offsets for the colour components of each pixel will gradually increase (or decrease) depending on the distance

Example

1. Clear all modifiers and switch @setsphere to 'ca' mode

   @clear,setsphere=n,setsphere_mode:3=force

2. Shift the red channel to the left by 8 pixels and blue to the right by 8 pixels

   @setsphere_param:8/0/-8/0=force

3. Increase the color shifts but blend back with the original colour at 50% (animate the change across 5 seconds)

   @setsphere_tween:5=force,setsphere_param:0/-25/0/25=force,setsphere_valuemax:0.5=force,setsphere_tween=force

4. Enforce the effect only when >=10m away (only objects >10m away appear affected)

   @setsphere_distmin:10=force

(Step 2) Red shifted by 8 left and 0 down. Blue shifted by 8 right and 0 down.

(Step 3) Using valuemin/valuemax blends the original colour with the effect making it appear more like a ghost artifact

(Step 4) Inner sphere radius set to 10m

Mode: Pixelate

Command	Value(s)	Description
setsphere_mode	4	Switches @setsphere to pixelate mode
setsphere_param	<width>/<height>/0/0	Specifies the pixelate block size (in pixels) - last 2 params are unused by this mode
setsphere_distmin	<distance>	Sets the distance (in m) at which the effect should start
setsphere_distmax	<distance>	Sets the distance (in m) at which the effect should end
setsphere_distextend	1 or 0	Specify 1 (default) to extend the effect past the maximum distance or 0 to end it
setsphere_valuemin	-	Unused
setsphere_valuemax	-	Unused

Notes

• don't use @setsphere_distextend:1=force with a min/max distance value in this mode; just setting distmin will suffice (see examples)

Example

1. Clear all modifiers and switch @setsphere to 'pixelate' mode

   @clear,setsphere=n,setsphere_mode:4=force

2. Set the block size to 10x10 (everything is pixelated)

   @setsphere_param:10/10/0/0=force

3. Enforce the effect only when >=10m away (only objects >10m away appear pixelated)

   @setsphere_distmin:10=force

4. Tween to a block size of 25x25 in 15 seconds (and then reset the tween duration for following commands)

   @setsphere_tween:15=force,setsphere_param:25/25/0/0=force,setsphere_tween=force

(Step 2) Block size set to 10x10

(Step 3) Inner sphere radius set to 10m

(Step 4) Block size set to 25x25